開發與應用能源研究與管理2015 (4)●65●DOI: 10.16056/j. 1005-7676.2015.04.018降低88LKXA-20型循環水泵振動技術分析及應用琚烈濤，陶曬(江西中電電力工程有限責任公司，南昌330000)摘要:寧德發電公司2x:600 MW機組設有88LKXA-20型循環水泵4臺,江西中電電力貴溪項目部承接該廠循環水泵維護，從2007年2月正式進入維護至今，循環水泵運行狀況不太穩定，運行中泵振動超標，縮短了設備運行導命。不得不從檢修技術規程上進行研究革新,打破部分常規工藝方法,使用先進技術，創新工藝方法,目的使循環水泵振動值下降,降低缺陷發生率。通過實踐應用得以證明檢修工藝技術創新取得實效，改進技術具有實踐性和可操作性。技術改進主要針對循泵關鍵節點和主要檢修工藝進行分析探討，技術創新。近2年項目部采用改進檢修工藝大修的3B和3A循泵質量優良，振動值在0.02 mm/s以內,創歷史佳績。關鍵詞:工藝方法;振動超標;技術創新;實踐應用中圖分類號: TM621.6文獻標志碼: A文章編號: 1005-7676 (2015) 04- -0018-05Reduce 88LKXA-20 Circulating Water Pump VibrationAnalysis and ApplicationJU Lietao, TAO Sai(Jiangxi Electric Power Engineering Co., Ltd, Nanchang 30000, China)Abstract: Ningde Power Generation Company 2x600 MW unit has 88LKXA-20 type circulating pump 4, Jiangxi Guixielectric power plant project department to undertake the circulating pump maintenance, from February 2007 oficially enteredthe maintenance so far. Circulating pump is not stable operating conditions, the pump running excessive vibration, reducingthe equipment operating life. Had to overhaul technical regulations fom the research innovation, breaking part of theconventional processes, the use of advanced technology, innovative process for the purpose of the circulating pump vibrationvalue drops, reducing the defect rate. Applications can be proved through practice inspection technology innovation toachieve tangible results, improvements in technology have practicality and maneuverability. Technological improvementsaimed at key nodes through the pump and a major overhaul process was analyzed and discussed, technological innovation.The Ministry of nearly two years of the project to improve the use of good maintenance process overhaul 3B and 3Acirculation pump qualit, vibration within 0.02 mm/s, a record of success.Key words: process method; excessive vibration; technology innovation; practical application有檢查、測量、更換等工序。拆卸工作主要是對泵1常 規檢修工藝概述體進行解體，過程中記錄部分修前數據，作為組裝88LKXA-20型循環水泵解體檢修主要分為拆時的參考數據。如提升量、中心、支架與簡體間隙卸、修理、組裝3大步驟，在整個大修過程中又含及相對位置(用塞尺測量)、電機支座水平度、電機收稿日期: 2015-07-19 .作者簡介:琚烈濤(1986-), 男，江西上饒人，助理工程師，大學本科，畢業于武中國煤化工要研究方向:電力檢修技術、創新及管理。MYHCNMHG.